Keys dont always play?
Moderators: Feg, Gill the Piano, Melodytune
Keys dont always play?
I have just got back into playing the piano after buying my first house and having somewhere permanent to keep one.
I bought myself my first piano from a reputable dealer (I hope) on ebay (do the two go together?). It’s a Broadwood circa 1880 in a lovely walnut cabinet. The piano itself is in fantastic condition externally as I can see, and all the notes play (most of the time).
It was tuned before I bought it and has stayed in tune quite well since it was re-housed into my front room. Only the middle c and a few others have fallen flat, most of them are still in tune after 4 weeks.
I took it apart (as you do) to have a good look inside. The only issue im having with it is sometimes the keys don’t play, especially after playing for about 2-3 minutes. It also happens when you play softly.
Im a newbie to piano servicing but I would like to think I’m pretty handy. I know I should get someone pro to check it out, but everyone wants a call out fee! Probably understandable, but I want to learn more about the piano and how to look after, maintain and play properly so am keen to soak up as much advice from you Gurus as possible and do as much work myself as I can.
After taking it apart, I took a few photos of what, to my novice eyes, didn’t look quite right.
So finally, (sorry for the waffle) to my question…. Can anyone see anything untoward in the photos that needs immediate attention, or might be the cause of the keys not always playing?
Thanks in advance
after taking a second look at this pic, is this the main culprit? i do feel like a double hit sometimes? if there is this gap this may be what im feeling? a tap of the bottom then when it hits the string. if this gap exists, it might not then reach the string? hmm....
it looks like someone has turned this one upside down?! can you buy these felts easily?
thanks again
S
-
- Site Admin
- Posts: 3648
- Joined: 30 May 2003, 20:42
- Location: Lanc's
- Contact:
Re: Keys dont always play?
Post by Barrie Heaton »
Sounds like the jacks centres may be a bit stiff your tuner may put some CPL on them that may do the trick, if not ... then they will have to re centre the jacks and hammers
As to the parts being uneven that standard for a piano that has been neglected over the years. At least all the bits are there unlike some that come off Ebay
Get a tuner in in a few week to give it the once over
Barrie,
Web Master UK Piano Page
- Colin Nicholson
- Executive Poster
- Posts: 1704
- Joined: 04 Jul 2010, 19:15
- Location: Morpeth, Northumberland
- Contact:
Re: Keys dont always play?
Post by Colin Nicholson »
1st Photo: There should be a gap here between every lever body & damper wire button - but with the mechanism IN THE PIANO - however, as you have lifted the mechanism out & placed it on carpet, the gaps & geometry will be larger & change as the levers collapse slightly - so the gaps need to be created & adjusted with the mechanism in the piano, sitting on the keys.... however, I would leave them well alone - the wood will probably be quite brittle. The gaps here are intentional, and nothing to do with why the notes won't play. If the dampers mute the strings OK, best to leave them alone.
Last photo: These are the key capstan cloths. Reason the cloth has been reversed is due to the excess wear on the cloth (the end of the cloth closest to you doesnt come into contact with the undercarriage).... under each piece of cloth is a countersunk screw.... this has probably worn its way through the cloth?.... if you fold the cloth back, you'll see the screws.
The cloth is also only glued at one end, creating a flap under the screw.
Have a look on ebay for some box cloth - ????mm - but obviously cant measure it on a photo. However, whatever you replace with thicker & new materials, you will completely change the geometry of the movement - so you are best contacting a piano person who can give you some advice.
I hope that helps.
General help can be given, but I doubt a detailed synopsis will be given!
Colin Nicholson Dip. Mus. CMIT CLCM PTLLS
Piano tuning & repairs. Full UK restoration service
http://www.aatuners.com
Tuition ~ Accompaniment ~ Weddings
http://www.pianotime1964.com
Member of The Guild of Master Craftsmen
- Colin Nicholson
- Executive Poster
- Posts: 1704
- Joined: 04 Jul 2010, 19:15
- Location: Morpeth, Northumberland
- Contact:
Re: Keys dont always play?
Post by Colin Nicholson »
One of the problems with your photos showing the explanations in text, and that some of the parts are not in-line with each other is that you have taken all your photos with the mechanism removed. The back checks for instance (short wires with a wooden block & thick green felt).... when the mech. is removed, (and the fact that the piano is over 130 years old & not been regulated recently) is that they will all look higgildy piggildy when the mech is removed - due to the bridle tapes either broken off, the tape stretching, combined with the wires bending over time. When you put the mech back in the piano, then take some photos.... you will see the undercarriages raise slightly as they rest on those pieces of grey cloth (key capstans) and most of the gaps & parts misaligned will be different to when you took the photos on your carpet. If you can understand this, then I can explain a few things - but there are some trade secrets!!
Best advice would be for you to purchase the Haynes manual on pianos by John Bishop.... it is fully illustrated, names all the parts, and covers various sections on over-damped pianos.... but sometimes for the wrong reasons!
On your piano, if you look at the top of the damper wire, it will be threaded.... this is wound into a wooden block (which is pivotted on a pin), and then locked with a wooden circular 'bolt' .... rather like a locking nut. On some pianos there is a grub screw to hold the wire in place, even though it is still threaded. Some of the regulation process in adjusting these involves turning these wires up or down to create the right gap.... however beware! .... sometimes these wooden blocks break in half. These are generally the piano technician's worst nightmare - very awkward to adjust correctly - missing red felt washers? wires bent? and generally now are obsolete. Parts have to be hand-made, or pinched from another old mechanism.
During part of the mechanism cycle, there must be various small gaps between certain parts - rather like setting tappetts on an old car engine. Without these gaps, the mech will not function correctly/ dampers will lift prematurely etc......
Hope that has given you an insight....
Colin Nicholson Dip. Mus. CMIT CLCM PTLLS
Piano tuning & repairs. Full UK restoration service
http://www.aatuners.com
Tuition ~ Accompaniment ~ Weddings
http://www.pianotime1964.com
Member of The Guild of Master Craftsmen
Re: Keys dont always play?
Thanks for your great advice and your patients with a beginner!
Lesson one - done!
I will order the manual and begin to familiarise myself with technical terms. Like i said, i want to start to learn to play again, but also to service and maintain.
I think my best bet to start with will be to have someone come to inspect and service like you recommend, and i will bug them as much info as i can while they are there. i appreciate that small tolerances can make a big difference so its probably the best bet. they can then advise on the thickness of cloth i might need and any bits that need replacing/making up.
Any decent servicers local ish to Urmston Manchester anyone could recommend?
- Colin Nicholson
- Executive Poster
- Posts: 1704
- Joined: 04 Jul 2010, 19:15
- Location: Morpeth, Northumberland
- Contact:
Re: Keys dont always play?
Post by Colin Nicholson »
To give you an idea of some of the parts, their location, and their names, here is a cross section diagram of an over-damped mechanism similar to yours. (Some of the parts have been removed for clarity). You will see the jack tip rests under the hammer notch. Dont take any notice of the "missing gap" between the lever & damper wire wooden dolly - this is just a general diagram, not outlining the before - during and after movement.
Colin Nicholson Dip. Mus. CMIT CLCM PTLLS
Piano tuning & repairs. Full UK restoration service
http://www.aatuners.com
Tuition ~ Accompaniment ~ Weddings
http://www.pianotime1964.com
Member of The Guild of Master Craftsmen
Re: Keys dont always play?
i thought i would take another approach last night, rather than try and find the problem from the inside, i played for about 30mins paying attention to what was happening.
I can run my fingers up all the notes and they will all play. But when playing a tune with chords and quick movements etc, I go to press a note and its hard and nothing will play. If I let off and wait a fraction of a second and try again it hammers and plays.
So I’m guessing the hammer is struggling to return properly.
After a quick inspection the bridal straps are all in pretty good conditions and no sign of splits or tears so don’t think that is the culprit. Will have a look at the seating of the jack spring, and closer inspection of the jack in general to see if it is stiff, from the diagram (thanks) and the advice im guessing my problem will lie here ?
Just another quick note (no pun intended!) will it get better the more times its tuned? E.g its been sat now for about 4-5 weeks so should be settled, should I get it tuned now, then again when I have sorted this issues, or just wait until its sorted then get it tuned?
Have called two tuners, one is saying get the servicing sorted first then tune, the other is saying he will tune it, sort any bits that might need doing, but if more work needs doing then that will be done after the tune, then will need another tuning?
- Colin Nicholson
- Executive Poster
- Posts: 1704
- Joined: 04 Jul 2010, 19:15
- Location: Morpeth, Northumberland
- Contact:
Re: Keys dont always play?
Post by Colin Nicholson »
The bridle tapes wont have any effect - as I said before, and the jack spring will only do its job when the pin is replaced, and the bushing cloth in the flange is reamed out to accept a new slightly larger centre pin. The measurements here are to within 0.05mm - so an expert technician can only do this job, using a micrometer, pin extractor, reaming tools & centre pin cutters.
No.... wont make any difference if you have the piano tuned... the tuning is separate - nothing to do with the "mechanics" .
Here is another diagram below (cropped) - showing the areas that will need working on - in red. The tiny black dots on each flange is the centre pin & bushing cloth. The lever has 2 flanges, one at the back - for the lever itself (sometimes called the undercarriage or whippen), and the centre flange is for the jack. On some pianos, the flange part is on the jack - but they do the same job. When a new pin is inserted (after reaming) - the pin must be exactly 0.01mm smaller than the bushed hole - if the bushing hole is too small, the new pin will be too tight, and if too large, the parts will 'knock' or wobble from side to side.... same applies to the hammer flanges. On occasions, the weight of the parts & inertia is enough to bring everything back - but if you use the sustain pedal, the weight of the dampers & their wires do not add gravity - so the lever parts just get stuck mid-air. The bridle tape assists in the hammer return - it helps to 'tug' the hammer back (aswell as support all the levers from collapsing when you remove the mech.).... but again, if the pins are tight - the bridle tapes, springs, damper weight etc will be of no use.
If there are many notes to repin, your tuner may stop the tuning - and advise you that re-pinning is needed first - and if loads to do, they may prefer to take the mechanism away in their workshop. Also when you repin, the lever/hammer has to be removed from the action - so it is likely the bridle tape will need to be replaced aswell.... even though it has nothing to do with the repair! Bit like replacing a new exhaust pipe on a car.... if the brackets are rusty, or other associated parts unable to hold the new exhaust in place - they must also be replaced.... just like the tapes.
So.... here we are - your tuner will examine all three flanges PER NOTE.... the odd few they can repin in your home (and easier to remove the damper rail to get to the parts).... but if starts to become a ball-ache, expect a hefty(ish) quote for repinning. The repinning must be done first before any tuning - and thats if the piano CAN be tuned?
- overdampedactionflanges.jpg (38.14 KiB) Viewed 22535 times
Colin
Colin Nicholson Dip. Mus. CMIT CLCM PTLLS
Piano tuning & repairs. Full UK restoration service
http://www.aatuners.com
Tuition ~ Accompaniment ~ Weddings
http://www.pianotime1964.com
Member of The Guild of Master Craftsmen
Re: Keys dont always play?
im noticing it on both octaves either side of the middle c. (the notes that get played the most)
so i imagine its something someone is going to want to do at home rather than my front room with the dog licking his ear!
with those kind of tolerances its probably best left to a technician, however, if the bill is going to be more than the piano i may as well have a crack myself and if it works (ish) great, if not well it looks like i might be buying a new one anyway at this rate.
thanks again for all your great help and advice
- Colin Nicholson
- Executive Poster
- Posts: 1704
- Joined: 04 Jul 2010, 19:15
- Location: Morpeth, Northumberland
- Contact:
Re: Keys dont always play?
Post by Colin Nicholson »
If you want to save on call-out fees, and just pay for the repinning labour - let me know. If you know how to remove the offending levers & jacks/ hammers etc.,.. just take the action out, uncouple the bridle tape, unscrew them from their flanges (at the back) and pop them in the post to me complete. PM me for a price if needed, or just contact your local piano tuner.
I think we've just about covered everything..
cheers
Colin Nicholson Dip. Mus. CMIT CLCM PTLLS
Piano tuning & repairs. Full UK restoration service
http://www.aatuners.com
Tuition ~ Accompaniment ~ Weddings
http://www.pianotime1964.com
Member of The Guild of Master Craftsmen
- Colin Nicholson
- Executive Poster
- Posts: 1704
- Joined: 04 Jul 2010, 19:15
- Location: Morpeth, Northumberland
- Contact:
Re: Keys dont always play?
Post by Colin Nicholson »
Here is an image of a lever - showing the jack flange & lever flange repinned.... however on very old pianos (this is a Chappell upright - dated c.1930) - depending on the design of the jack flange, sometimes they are glued into the lever - like this one (similar to a tenon joint).... however, on a few notes, the notes didnt play AT ALL.... not even once from the beginning! and this was due to the bead of glue becoming brittle/ drying up & separating from the wood - hence you will see a gap (circled in red) .... so its not always the pin. As I started to assemble the mechanism - a few other jack flanges start to pop out of their sockets, so I rang the customer & took the decision to remove them.... cracked all the old glue off - on all 85 levers, and re-glued the whole lot.
This is the joys of piano restoration.... you sometimes never know .... and of course, because the new flange pins are forced into place, this would have also weakened the joint areas. However, this job was done in Feb 2011.... all back together - new pins/ new tapes/ new glue .... no phone calls as yet!!
Let me know if you need any help.....
Colin Nicholson Dip. Mus. CMIT CLCM PTLLS
Piano tuning & repairs. Full UK restoration service
http://www.aatuners.com
Tuition ~ Accompaniment ~ Weddings
http://www.pianotime1964.com
Member of The Guild of Master Craftsmen
- MarkGoodwinPianos
- Senior Poster
- Posts: 644
- Joined: 04 Nov 2006, 05:28
Re: Keys dont always play?
Post by MarkGoodwinPianos »
Well done chaps!
But... I can't help but add that I'd love to hear a video/sound recording of this piano being played. It's a straight-strung (oh no!) overdamper (oh no oh no!!) so I just can't help but think that if you are prepared to spend time and money on a piano you might as well start with something a bit more up to date.
In my opinion a dealer shouldn't be selling straight-strung overdampers to anyone who does not bring a technician prior to purchase. It's like selling a rotten old Austin Maestro with rotten sills and £2000 of welding needing doing, blowing smoke out the back and none of the wipers, windows, radio, fans, heaters or locks work. And trying to sell it for £200 as an "excellent 1st car". It's as bad as that in my opinion.
Can you upload a video?
I need to hear it. Make sure you play some fast chords where you let go as soon as you played so that we can tell how well the damping is working.
Fingers crossed you got a good one. I'd love to be wrong
email markgoodwinpianos@gmail.com with any Yamaha, Kawai, Bechstein or Steinway questions
- Colin Nicholson
- Executive Poster
- Posts: 1704
- Joined: 04 Jul 2010, 19:15
- Location: Morpeth, Northumberland
- Contact:
Re: Keys dont always play?
Post by Colin Nicholson »
A regular punter of mine had his piano pitch-raised about 2 years ago - Bechstein Model 10 (I know!!) .... all went well, and ever since, he has nurtured the piano. I also regularly receive recordings of "Middle C" !!! sent to my email - so I can forewarn him before his next appointment. Nice touch!
Colin Nicholson Dip. Mus. CMIT CLCM PTLLS
Piano tuning & repairs. Full UK restoration service
http://www.aatuners.com
Tuition ~ Accompaniment ~ Weddings
http://www.pianotime1964.com
Member of The Guild of Master Craftsmen
- MarkGoodwinPianos
- Senior Poster
- Posts: 644
- Joined: 04 Nov 2006, 05:28
Re: Keys dont always play?
Post by MarkGoodwinPianos »
The lesson to learn is if you can't afford a proper piano just yet, WAIT! Don't get a cheap one, don't get a free one, don't get one from freecycle, just WAIT and SAVE UP!
I'd say spend an absolute minimum of £500 but even then you might enjoy a good 2nd hand digital in that price range over a tatty, tired Chappell/Rogers/Broadwood/Brimsmead/Mickleburgh/Zender/Bentley/etc
email markgoodwinpianos@gmail.com with any Yamaha, Kawai, Bechstein or Steinway questions
- Colin Nicholson
- Executive Poster
- Posts: 1704
- Joined: 04 Jul 2010, 19:15
- Location: Morpeth, Northumberland
- Contact:
Re: Keys dont always play?
Post by Colin Nicholson »
http://www.youtube.com/watch?v=at8hdDCz ... e=youtu.be
I also sent the customer a small muting strip through the post! - I then uploaded his 'Middle C' tuning test it onto my PC.... then put my iPod up against the speakers!! .... and we have narration aswell by the customer! Unfortunately - its a bit blurred, but considering a major pitch raise (Bechstein Model 10) - its held its pitch quite well.
The things I do ...... !!
didnt make any difference to the cost of the next visit!!.... I visited again in December last year - had lunch in a nice pub in the Lakes - all paid for, and was also tipped for my journey of 126 miles!!
A bit of fun though - and anyone can do it to get a rough idea of their tuning!!
Colin Nicholson Dip. Mus. CMIT CLCM PTLLS
Piano tuning & repairs. Full UK restoration service
http://www.aatuners.com
Tuition ~ Accompaniment ~ Weddings
http://www.pianotime1964.com
Member of The Guild of Master Craftsmen
-
- Site Admin
- Posts: 3648
- Joined: 30 May 2003, 20:42
- Location: Lanc's
- Contact:
Re: Keys dont always play?
Post by Barrie Heaton »
Barrie
Web Master UK Piano Page
- Main Site Menu
-
Home
Piano Tuners
Piano Makers
Piano Teachers
Piano Accompanists
Piano Entertainers
Piano Shops
Piano Removals
French Polishers
Piano Rehearsal Rooms
Piano Hire
Pianos For Sale
Piano Parts
Piano History
Piano Forum
Piano Music
Piano Events
Advertise
Advanced Search Contact Site Admin
Help with a listing
Sitemap
Main Terms And Conditions
-
- Recent Listings